Page Header Logo Applied Science and Engineering Progress

Home > ONLINE FIRST > Rashid

Optimization and High-Efficiency Photocatalytic Degradation of Petroleum Refinery Wastewater using SiO₂/TiO₂ Nanocomposite under UV Irradiation

Sarmad Abdulrazzaq Rashid, Wadood Taher Mohammed

Abstract


The critical issue of environmental contamination caused by petroleum refinery wastewater (PRW) has attracted significant attention from researchers due to its harmful effects on human health and ecosystems. The real PRW was successfully treated using Silica-Titania (SiO2/TiO2, with a weight ratio of 2.5/97.5%) as a novel photocatalyst to remove organic compounds from real wastewater in a newly designed photocatalytic radiation chamber. SiO2/TiO2 was prepared by the sol-gel technique and assessed by the XRD, FTIR, FESEM, EDAX, AFM, and BET analysis. Response surface methodology was used to optimize solution pH, catalyst dosage, and reaction time. The results showed that SiO2/TiO2 dosage had the most significant impact on the COD reduction efficiency at optimal conditions of pH 3, SiO2/TiO2 dosage 2.29 g/L, and time 5.46 h, achieving 94% COD removal and a correlation coefficient of 98.54%, with an energy consumption of 1.719 kWh/L. SiO2/TiO2 maintained excellent stability after undergoing five cycles, achieving more than 87.8 % reduction of COD. The outcomes highlighted the synergistic effect between the SiO2/TiO2 photocatalyst and the new chamber design, showing significant enhancements in PRW treatment. Despite these promising results, the study was limited to a single PRW sample and a specific UV intensity. The designed photocatalyst can be examined for various wastewater compositions, scale-up feasibility, and long-term operational stability. Finally, the process revealed efficient performance and showed potential to be a cost-effective and eco-friendly approach for COD reduction from PRW.

Keywords



[1]  S. K. Kamal, Z. M. Mustafa, and A. S. Abbas, “Reaction kinetics and mass transfer of photocatalytic fenton for phenol degradation in a petroleum refinery wastewater,” Tikrit Journal of Engineering Sciences, vol. 32, no. 1, pp. 1–11, 2025.

[2]  M. Jiad and A. H. Abbar, “Treatment of petroleum refinery wastewater by sono fenton process utilizing the in-situ generated hydrogen peroxide,” Al-Khwarizmi Engineering Journal, vol. 19, no. 2, pp. 52–67, 2023, doi: 10.22153/kej.2023.04.002.

[3]     S. Yadav and S. Kamsonlian, “Progress on the development of techniques to remove contaminants from wastewater: A review,” Applied Science and Engineering Progress, vol. 16, no. 3, 2023, Art. no. 6729, doi: 10.14416/j.asep.2023.02.001.

[4]     S. Jafarinejad and S. C. Jiang, “Current technologies and future directions for treating petroleum refineries and petrochemical plants (PRPP) wastewaters,” Journal of Environmental Chemical Engineering, vol. 7, no. 5, 2019, Art. no. 103326, doi: 10.1016/j.jece.2019.103326.

[5]     M. M. Jiad and A. H. Abbar, “Treatment of petroleum refinery wastewater by an innovative electro-Fenton system: Performance and specific energy consumption evaluation,” Case Studies in Chemical and Environmental Engineering, vol. 8, 2023, Art. no. 100431, doi: 10.1016/j.cscee.2023.100431.

[6]     W. F. Elmobarak, B. H. Hameed, F. Almomani, and A. Z. Abdullah, “A review on the treatment of petroleum refinery wastewater using advanced oxidation processes,” Catalysts, vol. 11, no. 7, 2021, Art. no.  782, doi: 10.3390/catal11070782.

[7]     S. J. Kulkarni, “Biological treatment of petroleum wastewater: A review on research and studies,” International Journal of Petroleum and Petrochemical Engineering, vol. 2, pp. 17–21, 2016, doi: 10.20431/2454-7980.0202004.

[8]     S. M. Al-Jubouri et al., “Multicomponent equilibrium isotherms and kinetics study of Heavy metals removal from aqueous solutions using electrocoagulation combined with mordenite zeolite and ultrasonication,” Applied Science and Engineering Progress, vol. 18, no. 1, 2025, Art. no. 7484, doi: 10.14416/j.asep.2024.07.011.

[9]     O. Hartal et al., “Combined natural flotation and chemical precipitation for the treatment of vegetable oil refinery wastewater,” International Journal of Environmental Science and Technology, vol. 21, no. 10, pp. 7295–7306, 2024, doi: 10.1007/s13762-024-05470-6.

[10]  S. M. Al-Jubouri, H. A. Al-Jendeel, S. A. Rashid, and S. Al-Batty, “Antibiotics adsorption from contaminated water by composites of ZSM-5 zeolite nanocrystals coated carbon,” Journal of Water Process Engineering, vol. 47, 2022 Art. no. 102745, doi: 10.1016/j.jwpe.2022.102745.

[11]  T. Altaee, S. A. Rashid, and M. F. Abdul Jabbar, “Treatment of used lubricant oil by solvent extraction,” Iraqi Journal of Chemical and Petroleum Engineering, vol. 23, no. 1, pp. 43–50, 2022, doi: 10.31699/ijcpe.2022.1.6.

[12]  Z. A. Ibrahim and A. F. Al-Alawy, “Synthesis and characterization of dual functional potassium doped MWCNT composites (K@ Fe3O4@ MWCNT and TEG-K/MWCNT) as innovative osmotic agents for forward osmosis processes,” Journal of Molecular Liquids, vol. 437, 2025, Art. no. 128452, doi: 10.1016/j.molliq.2025.128452.

[13]  A. G. Saleem and S. M. Al-Jubouri, “Efficient separation of organic dyes using polyvinylidene fluoride/polyethylene glycol-tin oxide (PVDF/PEG-SnO2) nanoparticles ultrafiltration membrane,” Applied Science and Engineering Progress, vol. 17, no. 4, 2024, Art. no.  7523, doi: 10.14416/j.asep.2024.08.001.

[14]  S. Ungwiwatkul, M. Jaikua, K. Prasertboonyai, P. Thana, A. Tamman, and K. Matra, “Plasma-activated municipal wastewater (PAMW): Revolutionizing municipal wastewater into high-value liquid fertilizer for duckweed cultivation through air plasma treatment,” Applied Science and Engineering Progress, vol. 18, no. 3, 2025, Art. no.  7791, doi: 10.14416/j.asep.2025.04.002.

[15]  A. S. Adday and S. M. Al-Jubouri, “Developing a versatile visible-light-driven polyvinylidene fluoride/Ag2O@CRA photocatalytic membrane for efficient treatment of organic pollutants-contained wastewater,” Journal of Water Process Engineering, vol. 73, 2025, Art. no.  107713, doi: doi.org/10.1016/j.jwpe.2025.107713.

[16]  Q. K. Hameed and W. T. Mohammed, “Treatment of wastewater from oil refineries by a combination of electrocoagulation with photocatalytic processes using immobilized nano-zinc oxide photocatalyst,” Journal of Ecological Engineering, vol. 25, no. 11, pp. 109–123, 2024, doi: 10.12911/22998993/ 192671.

[17]  I. Oller, S. Malato, and J. A. Sanchez-Perez, “Combination of advanced oxidation processes and biological treatments for wastewater decontamination-A review,” Science of the Total Environment, vol. 409, no. 20, pp. 4141–4166, 2011, doi: 0.1016/j.scitotenv.2010.08.061.

[18]  S. A. Rashid and W. T. Mohammed, “Effective oxidation of phenol compound by silica oxide-titanium dioxide photocatalyst in a well-designed photocatalysis reactor,” Chemistry Africa, vol. 8, pp. 3773–3788, 2025, doi: 10.1007/s42250-025-01375-0.

[19]  Y. Y. Lim, A. M. A. Zaidi, and A. Miskon, “Composing on-program triggers and on-demand stimuli into biosensor drug carriers in drug delivery systems for programmable arthritis therapy,” Pharmaceuticals, vol. 15, no. 11, 2022, Art. no. 1330, doi: 10.3390/ph15111330.

[20]  Y. Y. Lim, A. M. A. Zaidi, M. Haque, and A. Miskon, “Relationship between tumorigenesis, metastasis, immune evasion, and chemoresistance in osteosarcoma therapy,” Journal of Applied Pharmceutical Science, vol. 14, no. 1, pp. 064–079, 2024, doi: 10.7324/JAPS.2023.149907.

[21]  Y. Y. Lim, A. Miskon, A. M. A. Zaidi, M. M. H. M. Ahmad, and M. A. Bakar, “Structural characterization analyses of low brass filler biomaterial for hard tissue implanted scaffold applications,” Materials, vol. 15, no. 4, 2022, Art. no. 1421, doi: 10.3390/ma15041421.

[22]  Y. Y. Lim, A. Miskon, and A. M. A. Zaidi, “Structural strength analyses for low brass filler biomaterial with anti-trauma effects in articular cartilage scaffold design,” Materials, vol. 15, no. 13, 2022, Art. no. 4446, doi: 10.3390/ma15134446.

[23]  Y. Y. Lim, A. Miskon, A. M. A. Zaidi, M. M. H. M. Ahmad, and M. A. Bakar, “Numerical simulation study on relationship between the fracture mechanisms and residual membrane stresses of metallic material,” Journal of Functional Biomaterials, vol. 13, no. 1, 2022, Art. no. 20, doi: 10.3390/jfb13010020.

[24]  N. J. Sadek, S. M. Alradhi, T. M. Albayati, I. K. Salih, and N. Elmi Fard, “Recent developments in petroleum wastewater treatment based on advanced oxidation processes: A review,” Iranian Journal of Chemistry and Chemical Engineering, vol. 44, no. 4, pp. 1089–1120, 2025, doi: 10.30492/ijcce.2025. 2044930.6870.

[25]  K. Rajeshwar, C. R. Chenthamarakshan, S. Goeringer, and M. Djukic, “Titania-based heterogeneous photocatalysis. Materials, mechanistic issues, and implications for environmental remediation,” Pure and Applied Chemistry, vol. 73, no. 12, pp. 1849–1860, 2001. doi: 10.1351/pac200173121849.

[26]  J. R. Bolton, “Solar detoxification,” Solar Energy, vol. 56, no. 5, 1996, doi: 10.1016/0038-092x(96)81766-x.

[27]  S. M. Abbas and S. M. Al-Jubouri, “ZrO2 nanoparticles filler-based mixed matrix polyethersulfone/cellulose acetate microfiltration membrane for oily wastewater separation,” Applied Science and Engineering Progress, vol. 18, no. 1, 2025, Art. no. 7599, doi: 10.14416/j.asep.2024.10.001.

[28]  Y. Y. Lim, A. M. A. Zaidi, and A. Miskon, “Combining copper and zinc into a biosensor for anti-chemoresistance and achieving osteosarcoma therapeutic efficacy,” Molecules, vol. 28, no. 7, 2023, Art. no. 2920, doi: 10.3390/molecules28072920.

[29]  Y. Y. Lim, A. Miskon, and A. M. Zaidi, “CuZn complex used in electrical biosensors for drug delivery systems,” Materials, vol. 15, no. 21, 2022, Art. no. 7672, doi: 10.3390/ma15217672.

[30]  J. M. Herrmann, M. N. Mozzanega, and P. Pichat, “Oxidation of oxalic acid in aqueous suspensions of semiconductors illuminated with UV or visible light,” Journal of Photochemistry, vol. 22, no. 4, pp. 333–343, 1983, doi: 10.1016/0047-2670(83)85012-6.

[31]  K. T. Amakiri, A. Angelis-Dimakis, and A. R. Canon, “Recent advances, influencing factors, and future research prospects using photocatalytic process for produced water treatment,” Water Science and Technology, vol. 85, no. 3, pp. 769–788, 2022, doi: 10.2166/wst.2021.641.

[32]  M. Besancon et al., “Influence of the porous texture of SBA-15 mesoporous silica on the anatase formation in TiO2-SiO2 nanocomposites,” New Journal of Chemistry, vol. 40, no. 5, pp. 4386–4397, 2016, doi: 10.1039/C5NJ02859K.

[33]  S. M. Park et al., “Hybrid CuxO-TiO2 heterostructured composites for photocatalytic CO2 reduction into methane using solar irradiation: Sunlight into Fuel,” American Chemical Society Omega, vol. 1, no. 5, pp. 868–875, 2016, doi: 10.1021/acsomega.6b00164.

[34]  G. R. Silva et al., “Photocatalytic modified membranes with dopamine and GO-TiO2 applied to petroleum refinery wastewater treatment,” Separation and Purification Technology, vol. 361, 2025, Art. no. 131621, doi: 10.1016/j.seppur.2025.131621.

[35]  A. Balakrishnan, K. Gopalram, and S. Appunni, “Photocatalytic degradation of 2,4-dicholoro phenoxya cetic acid by TiO2 modified catalyst: Kinetics and operating cost analysis,” Environmental Science and Pollution Research, vol. 28, pp. 33331–33343, 2021, doi: 10.1007/s11356-021-12928-4.

[36]  Y. J. O. Asencios, V. S. Lourenco, and W. A. Carvalho, “Removal of phenol in seawater by heterogeneous photocatalysis using activated carbon materials modified with TiO2,” Catalysis Today, vol. 388, pp. 247–258, 2022, doi: 10.1016/j.cattod.2020.06.064.

[37]  S. Bai et al., “Improvement of TiO2 photocatalytic properties under visible light by WO3/TiO2 and MoO3/TiO2 composites,” Applied Surface Science, vol. 338, pp. 61–68, 2015, doi: 10.1016/j.apsusc.2015. 02.103.

[38]  Y. Liu, F. Xin, F. Wang, S. Luo, and X. Yin, “Synthesis, characterization, and activities of visible light-driven Bi2O3-TiO2 composite photocatalysts,” Journal of Alloys and Compounds, vol. 498, no. 2, pp. 179–184, 2010, doi: 10.1016/j.jallcom.2010.03.151.

[39]  R. Ghamarpoor, A. Fallah, and M. Jamshidi, “A review of synthesis methods, modifications, and mechanisms of ZnO/TiO2-based photocatalysts for photodegradation of contaminants,” American Chemical Society Omega, vol. 9, no. 24, pp. 25457–25492, 2024, doi: 10.1021/acsomega.3c08717.

[40]  P. Miądlicki, P. Rychtowski and B. Tryba, “Coating of expanded polystyrene spheres by ­TiO2 and TiO2-SiO2 thin films,” Journal of Materials Research, vol. 39, pp. 1473–1488, 2024, doi: 10.1557/s43578-024-01319-3.

[41]  Y. Cheng, F. Luo, Y. Jiang, F. Li, and C. Wei, “The effect of calcination temperature on the structure and activity of TiO2/SiO2 composite catalysts derived from titanium sulfate and fly ash acid sludge,” Colloids and Surfaces A : Physicochemical and Engineering Aspects, vol. 554, pp. 81–85, 2018, doi: 10.1016/j.colsurfa.2018.06.032.

[42]  T. Cetinkaya, L. Neuwirthov, K. Kutlakova, V. Tomasek, and H. Akbulut, “Synthesis of nanostructured TiO2/SiO2 as an effective photocatalyst for degradation of acid orange,” Applied Surface Science, vol. 279, pp. 384–390, 2013, doi: 10.1016/j.apsusc.2013.04.121.

[43]  J. Li et al., “Advances in Z scheme semiconductor photocatalysts for the photoelectrochemical applications: A review,” Carbon Energy, vol. 4, no. 3, pp. 294–331, 2022, doi: 10.1002/cey2.179.

[44]  D. Wang et al., “Engineering and modeling perspectives on photocatalytic reactors for water treatment,” Water Research, vol. 202, 2021, Art. no. 117421, doi: 10.1016/j.watres.2021.117421.

[45]  J. Mei, X. Gao, J. Zou, and F. Pang, “Research on photocatalytic wastewater treatment reactors: design, optimization, and evaluation criteria,” Catalysts, vol. 13, no. 6, 2023, Art. no. 974, doi: 10.3390/cata l13060974.

[46]  I. J. Ani, U. G. Akpan, M. A. Olutoye, and B. H. Hameed, “Photocatalytic degradation of pollutants in petroleum refinery wastewater by TiO2- and ZnO-based photocatalysts: Recent development,” Journal of Cleaner Production, vol. 205, pp. 930-954, 2018, doi: 10.1016/j.jclepro. 2018.08.189.

[47]  R. Vijayalakshmi and V. Rajendran, “Synthesis and characterization of nano-TiO2 via different methods,” Archives Applied Science Research, vol. 4, no. 2, pp. 1183–1190, 2012.

[48]  N. F. Azlan, S. Akhbar, S. H. Hanipah, and R. W. Sharudin, “A short review on synthesis and characterisation of nano SiO2/TiO2 composite for insulation application,” Malaysian Journal of Chemical Engineering and Technology (MJCET), vol. 4, no. 2, pp. 155–166, 2021.

[49]  C. G. Joseph, Y. H. Taufiq-Yap, G. L. Puma, K. Sanmugam, and K. S. Quek, “Photocatalytic degradation of cationic dye simulated wastewater using four radiation sources, UVA, UVB, UVC and solar lamp of identical power output,” Desalination and Water Treat, vol. 57, no. 17, pp. 7976–7987, 2016, doi: 10.1080/19443994.2015.1063463.

[50]  M. Zarei, A. R. Khataee, R. Ordikhani-Seyedlar, and M. Fathinia, “Photoelectro-Fenton combined with photocatalytic process for degradation of an azo dye using supported TiO2 nanoparticles and carbon nanotube cathode: neural network modeling,” Electrochimica Acta, vol. 55, no. 24, pp. 7259–7265, 2010, doi: 10.1016/j.electacta.2010. 07.050.

[51]  A. Hosseini, J. Foroughi, M. Sabzehmeidani, and M. Ghaedi, “Heterogeneous photoelectro-Fenton using ZnO and TiO2 thin film as photocatalyst for photocatalytic degradation Malachite Green,” Applied Surface Science Advances, vol. 6, 2021, Art. no. 100126, doi: 10.1016/j.apsadv.2021.100126.

[52]  H. Gobara, R. El-Salamony, D. Mohamed, M. Mishrif, Y. Moustafa, and T. Gendy, “Use of SiO2-TiO2 nanocomposite as photocatalyst for the removal of trichlorophenol: A kinetic study and numerical evaluation,” Chemistry and Materials Research, vol. 6, no. 6, pp. 63–82, 2014.

[53]  A. N. Kassob and A. H. Abbar, “Treatment of petroleum refinery wastewater by graphite-graphite electro fenton system using batch recirculation electrochemical reactor,” Journal of Ecological Engineering, vol. 23, no. 10, pp. 291–303, 2022.

[54]  H. M. Al-Tameemi, K. A. Sukkar, A. H. Abbar, and Z. K. Kuraimid, “Optimization of photocatalytic process with SnO2 catalyst for COD reduction from petroleum refinery wastewater using a slurry bubble photoreactor,” Case Studies in Chemical and Environmental Engineering, vol. 9, 2024, Art. no. 100687, doi: 10.1016/j.cscee.2024.100687.

[55]  M. Khraisheh, L. Wu, A. H. Al-Muhtaseb, A. B. Albadarin, and G. M. Walker, “Phenol degradation by powdered metal ion modified titanium dioxide photocatalysts,” Chemical Engineering Journal, vol. 213, pp. 125–134, 2012, doi: 10.1016/j.cej. 2012.09.108.

[56]  E. W. Rice, R. B. Baird, A. D. Eaton, and L. S. Clesceri, Standard Methods for the Examination of Water and Wastewater. Washington, DC: American Public Health Association American Water Works Association Water Environment Federation, 2012.

[57]  M. M. Jiad and A. H. Abbar, “Efficient wastewater treatment in petroleum refineries: Hybrid electro-fenton and photocatalysis (UV/ZnO) process,” Chemical Engineering Research and Design, vol. 200, pp. 431–444, 2023, doi: 10.1016/j.cherd.2023.10.050.

[58]  A. K. Hassan, M. A. Atiya, and Z. A. Mahmoud, “Photo-Fenton-like degradation of direct blue 15 using fixed bed reactor containing bimetallic nanoparticles: Effects and Box-Behnken optimization,” Environmental Technology & Innovation, vol. 28, 2022, Art. no. 102907, doi: 10.1016/j.eti.2022.102907.

[59]  M. Fathurrahman, A. Zulys, and J. Gunlazuardi, “Kinetic study and optimization of tetramethylthionine chloride photodegradation by iron-perylene MOF with hydrogen peroxide using response surface methodology,” Applied Science and Engineering Progress, vol. 18, no. 3, 2025, Art. no. 7683, doi: 10.14416/j.asep.2025.02.002.

[60]  N. Babajani and S. Jamshidi, “Investigation of photocatalytic malachite green   by iridium doped zinc oxide nanoparticles: Application of response surface methodology,” Journal of Alloys and Compounds, vol. 782, pp. 533–544, 2019, doi: 10.1016/j.jallcom.2018. 12.164.

[61]  J. Rumky, M. C. Ncibi, R. C. Burgos-Castillo, A. Deb, and M. Sillanpaa, “Optimization of integrated ultrasonic-Fenton system for metal removal and dewatering of anaerobically digested sludge by Box-Behnken design,” Science of The Total Environment, vol. 645, pp. 573–584, 2018, doi: 10.1016/j.scitotenv.2018.07.125.

[62]  D. C. Montgomery, Design and Analysis of Experiments. New York: John Wiley & Sons Inc., 2017.

[63]  M. Mohadesi and A. Shokri, “Treatment of oil refinery wastewater by photo-Fenton process using Box–Behnken design method: Kinetic study and energy consumption,” International Journal of Environmental Science and Technology, vol. 16, no. 11, pp. 7349–7356, 2019, doi: 10.1007/s13762-018-2153-5.

[64]  T. N. S. Ho, T. T. Nguyen, T. H. T. Pham, M. T. Ngo, and M. V. Le, “Photocatalytic degradation of phenol in aqueous solutions using TiO2/SiO2 composite,” Chemical Engineering Transactions, vol. 78, pp. 427–432, 2020, doi: 10.3303/CET2078072.

[65]  Y. Hendrix, A. Lazaro, Q. Yu, and J. Brouwers, “Titania-Silica composites: A review on the photocatalytic activity and synthesis methods,” World Journal of Nano Science and Engineering, vol. 5, no. 4, pp. 161–177, 2015, doi: 10.4236/wjnse.2015.54018.

[66]  S. Yohi, C. M. Wu, and R. T. Koodali, “A kinetic study of photocatalytic degradation of phenol over Titania–Silica mixed oxide materials under UV illumination,” Catalysts, vol. 12, no. 2, 2022, Art. no. 193, doi: 10.3390/catal12020193.

[67]  D. R. Eddy et al., “Photocatalytic phenol degradation by silica-modified titanium dioxide,” Applied Sciences, vol. 11, no. 19, 2021, Art. no. 9033, doi: 10.3390/app11199033.

[68]  A. S. Adday and S. M. Al-Jubouri, “Photocatalytic oxidative removal of the organic pollutant from wastewater using recyclable Ag2O@CRA heterojunction photocatalyst,” Case Studies in Chemical and Environmental Engineering, vol. 10, 2024, Art. no. 100852, doi: 10.1016/j.cscee. 2024.100852.

[69]  T. Degen, M. Sadki, E. Bron, U. Konig, and G. Nenert, “The highscore suite,” Powder Diffraction, vol. 29, pp. S13–S18, 2014.

[70]  M. A. Gatou, E. Fiorentis, N. Lagopati, and E. A. Pavlatou, “Photodegradation of rhodamine B and phenol using TiO2/SiO2 composite nanoparticles: A comparative study,” Water, vol. 15, no. 15, 2023, Art. no. 2773, doi: 10.3390/w15152773.

[71]  A. Duran, C. Serna, V. Fornes, and J. M. F. Navarro, “Structural considerations about SiO2 glasses prepared by sol-gel,” Journal of Non-Crystalline Solids, vol. 82, no. 1–3, pp. 69–77, 1986, doi: 10.1016/0022-3093(86)90112-2.

[72]  Y. D. Hou et al., “N-doped SiO2/TiO2 mesoporous nanoparticles with enhanced photocatalytic activity under visible-light irradiation,” Chemosphere, vol. 72, no. 3, pp. 414–421, 2008, doi: 10.1016/j. chemosphere.2008.02.035.

[73]  A. Siddiqa, S. Sabir, S. Hussain, and B. Muhammad, “Highly active mesoporous SiO2-TiO2 based nanocomposites for photocatalytic degradation of textile dyes and phenol,” European Journal of Chemistry, vol. 4, no. 4, pp. 388–395, 2013, doi: 10.5155/eurjchem.4.4.388-395.826.

[74]  A. R. Khataee, M. Zarei, and R. Ordikhani-Seyedlar, “Heterogeneous photocatalysis of a dye solution using supported TiO2 nanoparticles combined with homogeneous photoelectrochemical process : Molecular degradation products,” Journal of Molecular Catalysis A : Chemical, vol. 338, no. 1–2, pp. 84–91, 2011, doi: 10.1016/j.molcata.2011.01.028.

[75]  L. Cui, Y. Song, F. Wang, Y. Sheng, and H. Zou, “Electrospinning synthesis of SiO2-TiO2 hybrid nanofibers with large surface area and excellent photocatalytic activity,” Applied Surface Science, vol. 488, pp. 284–292, 2019, doi: 10.1016/j.apsusc.2019.05.151.

[76]  M. M. Jiad and A. H. Abbar, “Petroleum refinery wastewater treatment using a novel combined electro-Fenton and photocatalytic process,” Journal of Industrial and Engineering Chemistry, vol. 129, pp. 634–655, 2024, doi: 10.1016/j.jiec.2023.09.018.

[77]  S. G. Nasab, A. Semnani, A. Teimouri, M. J. Yazd, T. M. Isfahani, and S. Habibollahi, “Decolorization of crystal violet from aqueous solutions by a novel adsorbent chitosan/nanodiopside using response surface methodology and artificial neural network-genetic algorithm,” International Journal of Biological Macromolecules, vol. 124, pp. 429–443, 2019, doi: 10.1016/j.ijbiomac.2018. 11.148.

[78]  P. Ramesh, K. Saravanan, P. Manogar, J. Johnson, E. Vinoth, and M. Mayakannan, “Green synthesis and characterization of biocompatible zinc oxide nanoparticles and evaluation of its antibacterial potential,” Sensing and Bio-Sensing Research, vol. 31, 2021, Art. no. 100399, doi: 10.1016/j.sbsr.2021.100399.

[79]  H. Chaker, A. E. Attar, M. Djennas, and S. Fourmentin, “A statistical modeling-optimization approach for efficiency photocatalytic degradation of textile azo dye using cerium-doped mesoporous ZnO: A central composite design in response surface methodology,” Chemical Engineering Research and Design, vol. 171, pp. 198–212, 2021, doi: 10.1016/j.cherd.2021.05.008.

[80]  H. Derikvandi and A. Nezamzadeh-Ejhieh, “Designing of experiments for evaluating the interactions of influencing factors on the photocatalytic activity of NiS and SnS2: Focus on coupling, supporting and nanoparticles,” Journal of Colloid and Interface Science, vol. 490, pp. 628–641, 2017, doi: 10.1016/j.jcis.2016.11.102.

[81]  G. E. P. Box and D. W. Behnken, “Some new three level designs for the study of quantitative variables,” Technometrics, vol. 2, no. 4, pp. 455–475, 1960, doi: 10.1080/00401706.1960.10489912.

[82]  M. Rafiee, M. Sabeti, F. Torabi, and A. Rahimbakhsh, “COD reduction of aeration effluent by utilizing optimum quantities of UV/H2O2/O3 in a small-scale reactor,” Processes, vol. 10, no. 11, 2022, Art. no. 2441, doi: 10.3390/pr10112441.

[83]  E. K. Tetteh, D. B. Naidoo, and S. Rathilal, “Optimization of photo-catalytic degradation of oil refinery wastewater using Box-Behnken design,” Environmental Engineering Research, vol. 24, no. 4, pp. 711–717, 2019, doi: 10.4491/eer.2018.216.

[84]  H. M. Al-tameemi, K. A. Sukkar, A. H. Abbar, and Z. K. Kuraimid, “Optimization of photocatalytic process with SnO2 catalyst for COD reduction from petroleum refinery wastewater using a slurry bubble photoreactor,” Case Studies in Chemical and Environmental Engineering, vol. 9, 2024, Art. no. 100687, doi: 10.1016/j.cscee.2024.100687.

[85]  S. O. Tebbi et al., “green synthesis of sustainable and cost-effective TiO2-SiO2-Fe2O3 heterojunction nanocomposites for rhodamine B dye degradation under sunlight,” Water, vol. 17, no. 2, 2025, Art. no. 168, doi: 10.3390/w17020168.

[86]  A. Al-Hamdi and M. Sillanpaa, “Photocatalytic activities of antimony, iodide, and rare earth metals on SnO2 for the photodegradation of phenol under UV, solar, and visible light irradiations,” in Advanced Water Treatment, 2020, Amsterdam, Netherlands: Elsevier, pp. 129–288, doi: 10.1016/B978-0-12-819225-2.00004-1.

[87]  A. M. Abeish, H. M. Ang, and H. Znad, “Photocatalytic removal of pollutants from petroleum refinery effluent,” presented at the ICCPGE, Alkhoms, Libya, 2016, vol. 1, pp. 25–30.

[88]  N. S. Topare, M. Joy, R. R. Joshi, P. B. Jadhav, and L. K. Kshirsagar, “Treatment of petroleum industry wastewater using TiO2/UV photocatalytic process,” Journal of the Indian Chemical Society, vol. 92, no. 2, pp. 219–222, 2015.

[89]  H. K. Khalilova, S. A. Hasanova, and F. G. Aliyev, “Photocatalytic removal of organic pollutants from industrial wastewater using TiO2 catalyst,” Journal of Environmental Protection, vol. 9, pp. 691–698, 2018, doi: 10.4236/jep.2018.96043.

[90]  K. K. Hameed, W. T. Mohammed, and S. J. Mohammed, “Photocatalytic treatment of petroleum refinery wastewater by ZnO nanoparticles immobilized on a concrete substrate,” Iraqi Journal of Chemical and Petroleum Engineering, vol. 26, no. 3, pp. 113–122, 2025, doi: 10.31699/ijcpe.2025.3.10.

[91]  K. M. Abed, B. M. Kurji, S. A. Rashid, and B. A. Abdulmajeed, “Kinetics and thermodynamics of peppermint oil extraction from Peppermint leaves,” Iraqi Journal of Chemical and Petroleum Engineering, vol. 20, no. 4, pp. 1–6, 2019, doi: 10.31699/ijcpe.2019.4.1.

[92]  A. A. Okab and A. I. Alwared, “Photodegradation of tetracycline antibiotic by ternary recyclable Z-scheme g-C3N4/Fe3O4/Bi2WO6/Bi2S3 photocatalyst with improved charge separation efficiency: Characterization and mechanism studies,” Environmental Nanotechnology Monitoring & Management, vol. 19, 2023, Art. no. 100767, doi: 10.1016/j.enmm.2022.100767.

[93]  Z. H. Jabbar, S. E. Ebrahim, and S. H. Ammar, “Supported heterogeneous nanocomposites (SiO2/Fe3O4/Ag2WO4) for visible-light-driven photocatalytic disinfection against E. coli,” Materials Science in Semiconductor Processing, vol. 141, 2022, Art. no. 106427, doi: 10.1016/j.mssp.2021.106427.

[94]  N. M. Bahadur et al., “Ultrasonic assisted synthesis, characterization, and photocatalytic application of SiO2@TiO2 core shell nanocomposite particles,” Journal of Nanomaterials, vol. 2019, no. 1, 2019, Art. no. 6368789, doi: 10.1155/2019/6368789.

[95]  J. Saien and F. Shahrezaei, “Organic pollutants removal from petroleum refinery wastewater with nanotitania photocatalyst and UV light emission,” International Journal of Photoenergy, vol. 2012, 2012, Art. no. 703074, doi: 10.1155/2012/703074.

[96]  E. K. Tetteh, S. Rathilal, & D. B. Naidoo, “Photocatalytic degradation of oily waste and phenol from a local South Africa oil refinery wastewater using response methodology,” Scientific Reports, 2020, Art. no. 8850, doi: 10.1038/s41598-020-65480-5.

Full Text: PDF

DOI: 10.14416/j.asep.2026.04.011

Refbacks

  • There are currently no refbacks.


Copyright © 2025 by King Mongkut’s University of Technology North Bangkok. All rights reserved.