A Comparative Study of Different Materials for Manufacturing of Miniature Spur Gears by Spark Erosion Wire Cutting Process

Sujeet Kumar Chaubey, Kapil Gupta, Neelesh Kumar Jain

Abstract

Selection of suitable materials plays a key role in machining to produce durable and good quality micro parts and components as well as improve the productivity of machining processes. This paper presents the performance evaluation of Spark Erosion Wire Cutting (SEWC) for the manufacturing of miniature gears from different materials, namely stainless steel SS 304, aluminum 7075, copper, and brass. The major objectives of this performance evaluation of SEWC are to determine the effect of gear materials on the quality of the gears, the economic aspects of miniature gears, and the productivity of SEWC for fabricating miniature spur gears. The optimal range of SEWC parameters from past research works was considered for conducting experiments for this study. Four miniature spur gears were fabricated from each gear material. It was concluded from this study that 1) the use of SS 304 as miniature spur gear material results in a better surface finish than aluminum, copper and brass; 2) use of aluminum as miniature gear material is more productive than SS 304, copper and brass; 3) aluminum is more economical and material-efficient than SS 304, copper and brass to fabricate miniature gears by SEWC; 4) material lost in copper is higher as compared to other selected materials; and 5) cost of SS 304 miniature gear is more as compared to other fabricated gears by SEWC.

Keywords

References

[1] N. K. Jain and S. K. Chaubey, “Review of miniature gear manufacturing,” in Comprehensive Materials Finishing. Amsterdam, Netherlands: Elsevier, vol. 1, pp. 504–538, 2017, doi: 10.1016/B978- 0-12-803581-8.09159-1.

[2] S. Pathak, M. Böhm, J. Kaufman, J. Kopeček, S. Zulić, O. Stránský, A. Shukla, J. Brajer, L. Beránek, J. Radhakrishnan, D. Rostohar, and T. Mocek, “Surface integrity of SLM manufactured meso-size gears in laser shock peening without coating,” Journal of Manufacturing Processes, vol. 85, pp. 764–773, 2023, doi: 10.1016/j.jmapro. 2022.12.011.

[3] S. Pathak, N. K. Jain, and I. A. Palani, “Process performance comparison of ECH and PECH for quality enhancement of bevel gears,” Materials and Manufacturing Processes, vol. 30, no. 7, pp. 836–841, 2015, doi: 10.1080/10426914. 2014.994764.

[4] S. K. Chaubey, N. K. Jain, and K. Gupta, “A Comprehensive investigation on development of lightweight aluminium miniature gears by thermoelectric erosion machining process,” Micromachines, vol. 12, no. 10, Oct. 2021, Art. no. 1230, doi: 10.3390/mi12101230.

[5] S. P. Radzevich, Dudley’s Handbook of Practical Gear Design and Manufacture, 2nd ed. New York: CRC Press, USA, 2012.

[6] J. R. Davis, Gear Materials, Properties, and Manufacture. Ohio: ASM International, 2005.

[7] K. Gupta, N. K. Jain, R. F. Laubscher, Advanced Gear Manufacturing and Finishing- Classical and Modern Processes. Massachusetts: Academic Press, 2017.

[8] S. K. Chaubey and K. Gupta, “A review on Wire- EDM of bio titanium,” Reports in Mechanical Engineering, vol. 4, no. 1, pp. 141–152, Sep. 2023, doi: 10.31181/rme040103092023c.

[9] L. L. Alhadeff, D. T. Curtis, M. B. Marshall, and T. Slatte, ‘The application of wire electrical discharge machining (WEDM) in the prototyping of miniature brass gears,” Procedia CIRP, vol. 77, pp. 642–645, Sep. 2018, doi: 10.1016/ j.procir.2018.08.187.

[10] K. Gupta and N. K. Jain, “Analysis and optimization of the surface finish of the wire electrical discharge machined miniature gears,” Proceedings IMechE, Part B: Journal of Engineering Manufacture, vol. 228, no. 5, pp. 673– 681, Nov. 2013, doi: 10.1007/s00170-014-5772-0.

[11] S. Di, R. Haung, and G. Chi, “Study on micro-machining by micro-WEDM,” in Proceedings of 1st International IEEE Conference on Nano/ Micro Engineered and Molecular systems, pp. 615–619, 2006, doi: 10.1109/NEMS.2006. 334857.

[12] Y. Wanga, J. Chena, Z. Wang, and S. Dong, “Fabrication of micro gear with intact tooth profile by micro wire electrical discharge machining,” Journal of Materials Processing Technology, vol. 252, pp.137–147, Feb. 2018, doi: 10.1016/j.jmatprotec.2017.09.002.

[13] S. K. Chaubey and N. K. Jain, “Analysis and multi-response optimization of gear quality and surface finish of meso-sized helical and bevel gears manufactured by WSEM process,” Precision Engineering, vol. 55, pp. 293–309, Jan. 2019, doi: 10.1016/j.precisioneng.2018.09.019.

[14] R. M. Yusron, T. Prasetyo, and M. Pramudia, “Investigation of involute profile error on spur gear processed using Wire EDM,” IOP Conference Series: Materials Science and Engineering, vol. 1125, 2021, Art. no. 012119, doi: 10.1088/ 1757-899X/1125/1/012119.

[15] A. Raj, J. P. Misra, R. P. Singh, G. Singh, S. Sharma, and S. M. Eldin, “Performance analysis of WEDM during the machining of Inconel 690 miniature gear using RSM and ANN modeling approaches,” Reviews on Advanced Materials Science, vol. 62, no. 1, Mar. 2023, Art. no. 20220288, doi: 10.1515/rams-2022-0288

[16] M. Y. Ali, A. N. M. Karim, E. Y. T Adesta, A. F. Ismail, A. A. Abdullah, and M. N. Idris, “Comparative study of conventional and micro WEDM based on machining of meso/microsized spur gear,” International Journal of Precision Engineering and Manufacturing, vol. 11, no. 5, pp. 779–784, Oct. 2010, doi: 10.1007/s12541- 010-0092-2.

[17] K. Gupta, S. K. Chaubey, and N. K. Jain, “Exploring Wire-EDM for manufacturing the high quality meso-gears,” Procedia Materials Science, vol. 5, pp. 1755–1760, Sep. 2014, doi: 10.1016/j.mspro.2014.07.365.

[18] K. Gupta and N. K. Jain, “Comparative study of Wire-EDM and hobbing for manufacturing high-quality miniature gears,” Materials and Manufacturing Processes, vol. 29, no. 11–12, pp. 1470–1476, Oct. 2014, doi: 10.1080/10426914. 2014.94186.

Full Text: PDF

DOI: 10.14416/j.asep.2023.11.003

Refbacks

There are currently no refbacks.

Username
Password
Remember me