Page Header

Home > Vol 15, No 4 (Oct.–Dec. 2022) > Sichamnan

Effects of Parameters on Heat Transfer Characteristics of a Rectangular Cross Section Heat Pipe with Mesh Wick

Surachet Sichamnan, Anurak Rodbumrung

Abstract


This research investigated effects of parameters on heat transfer characteristics of a rectangular cross section heat pipe with mesh wick (RHP/MW). The working substance used Distilled Water and Refrigerant R-11. Heat loads at the evaporator were set at 20, 40, 60 and 80 W. Results revealed that, throughout the test, RHP/MW/ R-11 gave the highest heat transfer rate and average heat flux of 26.91 W and 2054.57 kW/m2 respectively. Heat Load of 80 W produced the lowest total thermal resistance of 0.4388 °C/W with the highest average thermal efficiency of 52.91%, the highest efficiency among the test cases. This is due to an increase of heat receiving areas of RHP/MW. More heat is transferred through the pipe wall to the wet perimeter of the working substance which caused the working substances in the evaporator to boil faster. The mesh wick also helped the condensed working substance to disperse around the inner tube wall and resulted in a thin film of the condensate liquid. This resulted in a higher heat transfer rate and heat flux for the RHP/MW. Mesh wick also generated capillary pressure that drew the condensed liquid back to the evaporator. The maximum capillary pressure obtained from the test was 93.29 N/m2 when the heat load of 80 W was applied to the RHP/MW/R-11. RHP/MW/R11 greatly enhances the heat transfer characteristics. Thus, it is suitable for application as an alternative to specific work sites that require smooth contact with heat receiving areas.

Keywords



[1] S. Sichamnan, T. Chompookham, and S. Rittidech, “Efficiency enhancement of solar panels using copper mesh wick heat pipe,” UBU Engineering Journal, vol. 9, no. 1, pp. 11–22, 2016.

[2] R. Sampan, Advanced Heat Pipe. Maha Sarakham, Thailand: Apichat Printing, 2013.

[3] A. Rodbumrung, “Influence of corrosion on the thermal performance and life time of heat pipe with sintered wick,” Ph.D. dissertation, Faculty of Engineering, Mahasarakham University, Maha Sarakham, 2016.

[4] P. Naphon, “On the performance of air conditioner with heat pipe for cooling air in the condenser,” Energy Conversion and Management, vol. 51, no. 11, pp. 2362–2366, 2010.

[5] L. L. Vasiliev, “Micro and miniature heat pipes – Electronic component coolers,” Applied Thermal Engineering, vol. 28, no. 4, pp. 266–273, 2008.

[6] H. Akachi, F. Polasek, and P. Stulc, “Pulsating heat pipes,” in the 5th International Heat Pipe Symposium, 1996, pp. 208–217.

[7] W. Srimuang, P. Khantikomol, and B. Krittacom, “An experimental investigation of effectiveness of a closed-end flat heat pipe heat exchanger,” KKU Engineering Journal, vol. 40, no. 1, pp. 21–27, 2013.

[8] L. G. Asirvatham, R. Nimmagadda, and S. Wongwises, “Heat transfer performance of screen mesh wick heat pipes using silver–water nanofluid,” International Journal of Heat and Mass Transfer, vol. 60, pp. 201–209, 2013.

[9] P. Naphon, P. Assadamongkol, and T. Borirak, “Experimental investigation of titanium nanofluids on the heat pipe thermal efficiency,” International Communications in Heat and Mass Transfer, vol. 35, no. 10, pp. 1316–1319, 2008.
[10] K. H. Do and S. P. Jang, “Effect of nanofluids on the thermal performance of a flat micro heat pipe with a rectangular grooved wick,” International Journal of Heat and Mass Transfer, vol. 53, no. 9–10, pp. 2183–2192, 2010.

[11] P. Amatachaya and W. Srimuang, “Comparative heat transfer characteristics of a flat two-phase closed thermosyphon (FTPCT) and a conventional two-phase closed thermosyphon (CTPCT),” International Communications in Heat and Mass Transfer, vol. 37, no. 3, pp. 293–298, 2010.

[12] N. Bhuwakietkumjohn and T. Parametthanuwat, “Heat transfer behaviour of silver particles containing oleic acid surfactant: Application in a two phase closed rectangular cross sectional thermosyphon (RTPTC),” Heat and Mass Transfer, vol. 53, no. 1, pp. 37–48, 2016.

[13] W. Srimuang, S. Rittidech, and B. Bubphachot, “Heat transfer characteristics of a vertical flat thermosyphon (VFT),” Journal of Mechanical Science and Technology, vol. 23, no. 9, pp. 2548– 2554, 2009.

[14] F. P. Incropera and D. P. DeWitt, Fundamentals of Heat and Mass Transfer. Michigan: Wiley, 1996.

[15] H. Li, F. Jiang, G. Qi, and X. Li, “Investigation of the thermal performance of a novel thermosyphon combined with fluidized bed heat transfer technology,” Powder Technology, vol. 374, pp. 40–48, 2020.

[16] K. H. Do, H. J. Ha, and S. P. Jang, “Thermal resistance of screen mesh wick heat pipes using the water-based Al2O3 nanofluids,” International Journal of Heat and Mass Transfer, vol. 53, no. 25–26, pp. 5888–5894, 2010.

[17] S. Satitpong, B. Supattra, and R. Sampan, “Study of parameters have effected to the heat pipe with mesh wick,” RMUTP Research, vol. 12, no. 2, pp. 172–183, 2018.

[18] M. M. Sarafraz, O. Pourmehran, B. Yang, and M. Arjomandi, “Assessment of the thermal performance of a thermosyphon heat pipe using zirconia-acetone nanofluids,” Renewable Energy, vol. 136, pp. 884–895, 2019.

[19] M. Kaya, “An experimental investigation on thermal efficiency of two-phase closed thermosyphon (TPCT) filled with CuO/water nanofluid,” Engineering Science and Technology, an International Journal, vol. 23, no. 4, pp. 812– 820, 2020.

[20] P. H. D. Santos, K. A. T. Vicente, L. Santos Reis, L. S. Marquardt, and T. A. Alves, “Modeling and experimental tests of a copper thermosyphon,” Acta Scientiarum Technology, vol. 39, no. 1, pp. 59–68, 2017.

[21] P. Thanya, R. Sampan, P. Adisak, Y. Ding, and S. Witharana, “Application of silver nanofluid containing oleicacid surfactant in a thermosyphon economizer,” Nanoscale Research Letters, vol. 6, 2011, Art. no. 315.

[22] D. Reay and P. Kew, Heat Pipe, Theory, Design and Application, 5th ed. Oxford, UK: Butterworth-Heinemann, 2006.

[23] A. Faghri, Heat Pipe Science and Technology. Washington, DC: Taylor & Francis, 1995.

[24] P. Terdtoon, Boiling. Chiang Mai, Thailand: Chiang Mai University, 2001.

[25] C. Piyanun, Heat Pipe Technologies. Phitsanulok, Thailand: Focus Printing, 2012.

[26] S. Sichamnan, “Flow patterns and heat transfer characteristic of two-phase closed rectangular cross sectional area thermosyphon,” Ph.D. dissertation, Department of Mechanical Engineering, Faculty of Engineering, Mahasarakham University, Maha Sarakham, 2019.

[27] T. Chompookham, S. Sichamnan, N. Bhuwakietkumjohn, and T. Parametthanuwat, “The rectangular two-phase closed thermosyphon: A case study of two-phase internal flow patterns behaviour for heat performance,” Archives of Thermodynamics, vol. 41, no. 3, pp. 223–254, 2020.

[28] S. V. Mutalikdesai and A. M. Kate, “Experimental investigation of an aluminium thermosyphon at normal operating conditions,” Journal of Thermal Engineering, vol. 6, no. 5, pp. 724–735, 2020.

[29] S. Sichamnan, “A mathematic model of photovoltaic solar collectors by heat pipe installation,” M.S. thesis, Department of Mechanical Engineering, Faculty of Engineering, Mahasarakham University, Maha Sarakham, 2015.

Full Text: PDF

DOI: 10.14416/j.asep.2021.11.010

Refbacks

  • There are currently no refbacks.


Copyright © 2024 by King Mongkut’s University of Technology North Bangkok. All rights reserved.