Numerical and Physical Investigation of the Mixing Process in Gas Stirred Ladle System

Sathaporn Lakkum, Patiparn Ninpetch, Nadnapang Phophichit, Pruet Kowitwarangkul, Atthasit Tawai, Somboon Otarawanna

Abstract

Secondary steelmaking or ladle metallurgy is one of the important processes that adjust and homogenize the chemical compositions and the temperature. In this process, argon gas is injected into the melt through porous plugs to accelerate the chemical reaction and the mixing. One of the indicators for the mixing efficiency is “the mixing time”. The purposes of this study were to investigate the effects of gas flow rate and purging system on the mixing time and flow characteristics by using numerical and physical investigation and to predict the velocity magnitude acting on the refractory wall by analyzing the effects of gas flow rate. A 1:5 scaled water model and a full-scale ladle model of Millcon steel PLC were used in the study. The numerical simulation modelling was carried out by using CFD commercial software Flow-3D. The results from the numerical simulation were in consistence with the experiment results. The simulation results showed that with the highest gas flow rate the reduction of the mixing time was around 36% and the velocity magnitude increased to approximately 44% in comparison with the lowest gas flow rate in the full-scale model. The area at the ladle wall near the liquid surface has a higher chance of the damage than other areas. Besides, employing the dual-plugs system led to approximately 33–49% shorter mixing time compared to the single-plug system. The results show that the gas flow rate affects the turbulent kinetic energy directly. However, high turbulent kinetic energy leads to open-eye size which results in re-oxidation and contamination. Therefore, it is important to optimize the flow rate to achieve both productivity and steel cleanliness.

Keywords

References

[1] D. Mazumdar and J. W. Evans, Modeling of Steelmaking Processes. Florida: CRC Press, 2009, p. 493.

[2] H. M. Issa, “Power consumption, mixing time, and oxygen mass transfer in a gas-liquid contactor stirred with a dual impeller for different spacing,” Journal of Engineering, vol. 2016, pp. 1–7, 2017.

[3] D. Mazumdar and R. I. L. Guthrie, “The physical and mathematical modelling of gas stirred ladle systems,” ISIJ International, vol. 35, no. 1, pp. 1–20, 1995.

[4] S. Lakkum and P. Kowitwarangkul, “Numerical investigations on the effect of gas flow rate in the gas stirred ladle with dual plugs,” in IOP Conference Series: Materials Science and Engineering, 2019, vol. 526, pp. 1–5.

[5] J. Mandal, S. Patil, M. Madan, and D. Mazumdar, “Mixing time and correlation for ladles stirred with dual porous plugs,” Metallurgical and Materials Transactions B, vol. 36, no. 4, pp. 479–487, 2015.

[6] K. M. A. Ali, “Parameters influence on mixing time of gas liquid agitation system,” Journal of University/Engineering Sciences, vol. 22, no. 2, pp. 403–412, 2014.

[7] F. Karouni, B. P. Wynne, J. T.-Silva, and S. Phillips, “Modeling the effect of plug positions and ladle aspect ratio on hydrogen removal in the Vacuum Arc Degasser,” Steel Research International, vol. 89, no. 5, pp. 1–8, 2018.

[8] S. Torres and M. A. Barron, “Numerical simulation of an argon stirred ladle with top and bottom injection,” Open Journal of Applied Science, vol. 6, no. 13, pp. 860–867, 2018.

[9] K. B. Owusu, T. Haas, P. Gajjar, M. Eickhoff, P. Kowitwarangkul, and H. Pfeifer, “Interaction of injector design, bubble size, flow structure, and turbulence in ladle metallurgy,” Steel Research International, vol. 90, no. 2, pp. 1–10, 2018.

[10] P. Gajjar, T. Haas, K. B. Owusu, M. Eickhoff, P. Kowitwarangkul, and H. Pfeifer, “Physical study of the impact of injector design on mixing, convection and turbulence in ladle metallurgy,” Engineering Science and Technology, an International Journal, vol. 22, no. 2, pp. 538–547, 2018.

[11] D. Mazumdar and R. I. L. Guthrie, “An assessment of a two phase calculation procedure for hydrodynamic modelling of submerged gas injection in ladles,” ISIJ International, vol. 34, no. 5, pp. 384–392, 1994.

[12] M. Madan, D. Satish, and D. Mazumdar, “Modeling of mixing in ladles fitted with dual plugs,” ISIJ International, vol. 45, no. 5, pp. 677–685, 2005.

[13] D. Mazumdar, H. B. Kim, and R. I. L. Guthrie, “Modelling criteria for flow simulation in gas stirred ladles: Experimental study,” Ironmaking and Steelmaking, vol. 27, no. 4, pp. 302–309, 2000.

[14] D. Mazumdar, P. Dhandapani, and R. Sarvanakumar, “Modeling and optimisation of gas stirred ladle systems,” ISIJ International, vol. 57, no. 2, pp. 286– 295, 2017.

[15] D. Mazumdar, G. Yamanoglu, R. Shankarnarayanan, and R. I. L. Guthrie, “Similarity considerations in the physical modelling of steel making tundish systems,” Steel Research International, vol. 66, no. 1, pp. 14–19 1995.

[16] V. Heller, “Scale effects in physical hydraulic engineering models,” Journal of Hydraulic Research, vol.49, no. 3, pp. 293-306, 2011.

[17] P. Kowitwarangkul, M. Kamonrattanapisud, E. Juntarasaro, and D. Sukam, “CFD simulation of moltenstell flow with isothermal condition in continuous casting tundish,” King Mongkut’s University of Technology North Bangkok International Journal of Applied Science and Technology, vol. 9, no. 2, pp. 71–77, 2016.

[18] N. Hasan, “Validation of CFD models using FLOW3D for a submerged liquid jet,” presented at the Ninth International Conference on CFD in the Minerals and Process Industries, Melbourne, Australia, Dec. 10–12, 2012.

[19] FLOW-3D. Flow Science, Inc. Accessed: Mar. 2, 2020 [Online]. Available: https://www.flow3d.com

[20] V. Yakhot, S. A. Orszag, S. Thangam, T. B. Gatski, and C. G. Speziale, “Development of turbulence models for shear flows by a double expansion technique,” Physics of Fluids A, vol. 4, no. 7, pp. 1510–1520, 1992.

[21] H. Liu, Z. Qi, and M. Xu, “Numerical simulation of fluid flow and interfacial behavior in threephase argon-stirred ladles with one plug and dual plugs,” Steel Research International, vol. 82, no. 4, pp. 440–458, 2011.

[22] M.-Y. Zhu, T. Inomoto, I. Sawada, and T.-C. Hsiao, “Fluid flow and mixing phenomena in the ladle stirred by argon through multi-tuyere,” ISIJ International, vol. 35, no. 5, pp. 472–479, 1995.

[23] A. Huang, H. Gu, M. Zhang, N. Wang, T. Wang, and Y. Zou, “Mathematical modeling on erosion characteristics of refining ladle lining with application of purging plug,” Metallurgical and Materials Transactions B, vol. 44, no. 3, pp. 744–749, 2013.

Full Text: PDF

DOI: 10.14416/j.asep.2020.07.001

Refbacks

There are currently no refbacks.

Username
Password
Remember me